LATAPOXY SP100
PRODUCT DESCRIPTION
Latapoxy SP 100 is a stainless, pigment free, colour fast epoxy grout
for grouting wall and floor installation of ceramics tile, brick and
stone. It is supplied as a factory proportioned kit consisting of epoxy
resins, hardener and silica filler, Latapoxy SP100 cleans with water
while fresh, and can be used on floors and walls in interior or exterior
applications of residential or commercial constructions.
ADVANTAGES
- It deals in new construction as well as for renovation.
- It is highly resistant to heavy traffic and rough usage.
- It cures at low temperature.
- Easy to clean with water when fresh, even on textured tiles.
- It is useful in active food preparation areas such as kitchen.
- It has superior stain resistance.
- It is easy to install and provides a finish as beautiful and durable as
the tile itself.
- It is normally recommended where stain and chemical resistance are
required: Kitchens, Cafeterias, Residential, Counter tops, Floors, Wall,
Bathroom and Swimming pools.
- It is non-flammable, easy to maintain and durable.
KEY FEATURES
- The grout is 100% epoxy and contain no water – soluble material, which
could lead to effloresce or molting.
- The grout never needs sealing and is dense and durable as the tile itself.
- The colour is already locked into the filler and cannot be washed away
be use of excess water or aggressive scrubbing when cleaning.
INSTALLATION
- SURFACE PREPARATION
Before starting to grout remove spacers and debris in grout joints and
remove dust and dirt using a wet sponge. Do not leave water standing in
joints. Room temperature must be between 90of (32oC).
- MIXING
Pour Latapoxy ® SP-100 Part A and Part B into clean mixing pail and mix
thoroughly by hand until liquids are completely blended. Add LATAPOXY®
SP-100 Part C powder and mix until uniformly blended.
- APPLICATION
Immediately pour entire contents of pail onto a flat surface (don’t leave
in pail ).
Spread with a sharp, firm rubber grout float.
Work the grout paste into the joints until completely filled. Use diagonal
stroke to pack the joints.
Insure that joint is filled and grout is not
just sitting on top (i.e. bridging the joint”).
- CLEANING
Remove excess grout from the face of the tiles with the edge of the grout
float.
Hold the float at a 90o angle and pull it at a 45o angle
diagonally across the joints and tile to avoid pulling out the material.
Clean using a white nylon pad and plenty of cool clean water.
| Chemical Name |
Continous Exposure |
Intermittent Exposure |
Splash Exposure |
| Milk |
R |
R |
R |
| ** Wine |
R |
R |
R |
| Ethanol |
NR (soft) |
R |
R |
| ** Potassium |
NR |
R |
R |
| Permangnate 10% |
R |
R |
R |
| ** Potassium |
R |
R |
R |
| Permangnate 1% |
R |
R |
R |
| Tannic Acid to 50% |
R |
R |
R |
| Tartaric Acid to 50% |
R |
R |
R |
| Phosphoric Acid to 80% |
R |
R |
R |
| * Sulfuric Acid to 20% |
R |
R |
R |
| OXalic Acid to 10% |
R |
R |
R |
| Lactic Acid to 5% |
R |
R |
R |
| Acetic Acid to 5% |
R |
R |
R |
| Sodium Hydroxide to 50% |
R |
R |
R |
| Saturated |
R |
R |
R |
| Benzoic Acid 5% |
R |
R |
R |
| Sea Water |
R |
R |
R |
| Fruit juice |
R |
R |
R |
| Methanol |
NR |
NR |
R |
| Mek |
NR |
NR |
R |
| Choloform |
NR |
NR |
R |
| Methylene |
NR |
NR |
NR |
| Toluene |
NR |
NR |
R |
| Xylene |
NR |
NR |
R |
* Chemical Resistent depends on exposure levels
Slash - Minor spil wipedup quickly such as in a laboratory
Intermittent - Expousure to chemical where clean up take place several times in a day such as in a commercial kitchen
Continuous - Heavy expousure to chemical where cleanup so less
Frequent such as in an industrial food plant
R = Recomment
NR = Not Recomment
Working Properties
Working Time ------------- 01 Hour
Time to Foot Traffic ------ 24 Hours
Time to Heavy Traffic --- 72 Hours
